Setting-of-technological-parameters-of-winding-machine

Switching-and-debugging-between-two-programs

 Toroidal transformer Taping Machine Instructions

      Let's now look at the tensioner, a threading process. First, the enameled wire passes through the ceramic ring at the bottom of the tensioner, and then passes through the wool felt above it. The clamping degree of the wool felt can be adjusted by passing the knob on the other side of the tensioner.

      Then go through the anti-jumper, and then go over the damping wheel on the tensioner once again, then pass through an anti-jumper again, and then pass through the guide wheel on the fishing rod, this is the threading process.

      Then how do we adjust to a more appropriate tension?   

       Let's take a look at the first one now. This handle is a tension switch. When the tension switch hits the top, the damping wheel doesn't work. When it is turned, it becomes very light. When the tension switch hits the bottom, the tensioner starts to work.

      If we want to increase the tension, we adjust the knob under the bottom of the tensioner, there is a scale in this position. Through this, adjust the damping size of the damping wheel on the tensioner.

      Then the handle at this position is used to adjust the back tension, which is the force of the fishing rod to bounce back. The general principle of our adjustment is that during the winding process, the fishing rod will not become weak under the interaction of the damping wheel. Sagging down, it will not be too strong and only a good swing requires a relatively large swing range, so that it can buffer and at the same time play a role in tensioning the enameled wire.

The company's CNC winding machine allows storage of 1000 sets of process data, and supports continuous execution of multiple sets of process data. The number of consecutive execution groups can be set from 2 to 1000 groups. This function is more complicated for the process and requires multiple external The intervention product provides great convenience and flexibility. The following winding machine operation video introduces the specific setting method.

Below we explain the two procedures of the Xiepu winding machine,

        Or continuous automatic execution between multiple programs,

        In other words, after bypassing the first program,

        Then the second program is executed automatically,

        No need for you to press the start button in the middle,

        Let's demonstrate,

        How the settings are set,

        First "step sequence setting" "input"

        In the second program,

        We put "autostart"

        Is now open,

        Then the "autostart" of the first program we have to close it,

        Because if this is the "autostart" of the first program,

        It will become an infinite loop,

        Turn it off now,

        Then press "Enter" and press "Reset"

        All right,

        Then we pay attention to the "" light in the lower left corner to turn on,

        Then we press start.

         The company's CNC winding machine supports the storage of 1000 sets of winding process data. After you complete the winding process data of a coil, it will be automatically saved. When you debug the next product, you only need to start the setting from the next program number The parameters are enough. When you need to produce the original product, you can also call it very conveniently. The video below illustrates the storage and recall of the company's winding machine process data.

         Let's introduce the process program of REPOSAL automatic winding machine.

         Store and recall.

         It can be stored in Xiepu's automatic winding machine controller.

         1000 different process procedures.

         How do we switch.

         Press the starting step.

         Press 1 and press enter.

         Then press the end order.

         Press 1 to enter and press to reset.

         Then we set the order by part and press the input.

         We will find that we continue to press enter.

         Press the words after entering.

         It will be set within the scope of Procedure 1.

         Starting point means to start from where.

         We can specify by this arrow.

         We can also enter numbers directly.

         For example, this is 36.5.

         We can enter 37.

         This is the starting point.

         Then we can specify the width for him.

         The width we are talking about is how big the line is.

         Winding back and forth within a range.

         Then we can set his enameled wire diameter.

         For example, the diameter of the enameled wire is 0.4 mm.

Setting of counting direction of winding machine controller:

         The REPOSAL's  winding machine controller has complete functions and a wide range of applications.Some customers have purchased our winding machine controller.As soon as we delivered the counting sensor, users sometimes find that when they are installed in the winding machine, the counting It will start counting from 9999.9 and become smaller and smaller. This is just because when you don't pay attention, install the counter in the opposite direction.At this time, we don't actually need to disassemble the installed machine. We have taken this into consideration. You need to change the counting direction on the controller.The video below shows that if you use our winding machine controller to change the counting direction.

Instructions for use of magnetic damping tensioner for winding machine

Assembly-of-high-frequency-transformer-winding-machine

           This video explains the structure of the high-frequency transformer winding machine. The general simple winding machine structure is roughly divided into several parts. The first part is the winding part, which is the winding shaft, and the second part is the winding part, which is the winding shaft. The mechanism that makes the enameled wire reciprocate while rotating. The third part is the wire passing mechanism, that is, the part between the enameled wire from the original cylinder to the tension mechanism. This part is usually composed of some bracket parts, and the fourth part is the tension part. To provide unequal tension required for winding the enameled wire on the coil, the fifth part is the winding head part, that is, the winding machine has passed the tensioner and obtained tension, and the part of the mechanism that will be wound on the coil. The high-frequency transformer is because of its design. Targeted, compared with the general simple winding machine, because its windings are more, the structure is compact, and the product requirements are not high, so there is no tensioner part, but because high-frequency transformers mostly require wall tape and insulating tape, So compared with the general simple winding machine, these two parts are more.

          Let's briefly introduce the structure of this transformer winding machine.

          Why did he name this winding machine the transformer winding machine?

          Because it can support multiple enameled wires of different specifications at the same time.

          Every enameled wire is from this position to this position.

          Then pass the ceramic circle.

          Then go through wool felt.

          Then there are different holes from small to large.

          Here are 4 such ceramic circles.

          Like this.

          In this way, he can clamp it all at once.

          The skeleton of the transformer is installed in this position.

          It can be wound with 4 enameled wires of different specifications at a time.

          Enameled wires of different specifications.

          This position is used to put the retaining wall tape on both sides of the high-frequency transformer skeleton.

          This position is used to place the insulating tape of the high-frequency transformer.

          So this machine is suitable for winding high frequency transformers.